Tea?

[classic33]

Tue is a half shift for me/us..
Nah, thought I'd show my face down the Shed..
trying to choose my next project..
I just have to put it down on paper...

Time off for good behaviour.
Any work done... words of advice offered...
You get to choose! Any ideas on what you want to have a go at?
On paper as in putting pen to paper. Pencil will be next.

Tea and biscuits been had no doubt.

 

[Bobby Mhor]

Time off for good behaviour.
Any work done... words of advice offered...
You get to choose! Any ideas on what you want to have a go at?
On paper as in putting pen to paper. Pencil will be next.

Tea and biscuits been had no doubt.

Nah, I just do some cleaning up...
See image, blue PETG, other PLA..
same original file just adapted for melting point and print bed...
PETG is stronger and could be used outdoor..
PLA is weaker etc etc..
I have ordered grey PETG....

Simple but effective, I've made the hole slightly undersized so I can screw on the patch lead, the pliers are downstairs, legs are 2cm tall..
The thickness of the plate is 4mm but possibly 2mm will be better. The original I saw had a 2mm one.
I have no right-hand plug connections. I'll right that next east order, the hole is maybe slightly tight, but pliers soon got that sorted, so the final one needs tweaking

 

[classic33]

Nah, I just do some cleaning up...
See image, blue PETG, other PLA..
same original file just adapted for melting point and print bed...
PETG is stronger and could be used outdoor..
PLA is weaker etc etc..
I have ordered grey PETG....
View attachment 782564
Simple but effective, I've made the hole slightly undersized so I can screw on the patch lead, the pliers are downstairs, legs are 2cm tall..
The thickness of the plate is 4mm but possibly 2mm will be better. The original I saw had a 2mm one.
I have no right-hand plug connections. I'll right that next east order, the hole is maybe slightly tight, but pliers soon got that sorted, so the final one needs tweaking

So yer just an unpaid janitor who pays to clean up after someone else...
From the picture I can see little difference, colour aside. 3" X 3"(or 80mm X 80mm)?
Do the pliers being downstairs have a connection with the legs being 2cm long.
Base/stand for an aerial.
Does the colour affect the strength of the finished piece. Better the hole too small than too large, you can always make it larger.
Needle nose pliers by chance.

 

[Bobby Mhor]

Good morning
Hal shift with the girls today..
They are about to land...
Got two panels of the fence painted, jeez, slats are murder, the fronts? no problem but them sides..
Anyhow, brownie points added to my good deed card

 

[Bobby Mhor]

So yer just an unpaid janitor who pays to clean up after someone else...
From the picture I can see little difference, colour aside. 3" X 3"(or 80mm X 80mm)?
Do the pliers being downstairs have a connection with the legs being 2cm long.
Base/stand for an aerial.
Does the colour affect the strength of the finished piece. Better the hole too small than too large, you can always make it larger.
Needle nose pliers by chance.

I did it for years as a Parkie..
never fazes me a bit of cleaning...
Must get my intended project on paper at some point..
as above, my artistic slopping on earlier..
Enjoying with a couple of ginger snaps, luvly jubbly..

Colour, no..
It's the material. It determines whatever its uses are.
Ordered a grey PETG and a different make so interesting to run a test piece to see how it lays down, reading some reviews, some are a bit fickle to work with, like my PLA is done using any of four makes.

Enjoying the quiet before Storm Toodles arrive...

 

[classic33]

Good morning
Hal shift with the girls today..
They are about to land...
Got two panels of the fence painted, jeez, slats are murder, the fronts? no problem but them sides..
Anyhow, brownie points added to my good deed card

Owdo
Hal shift! They being good to you...
You didn't try running when they did land, did you.
Thought you'd finished the fencing work for the year.
You tried using a roller for between them to get those sides.
Points, brownie or otherwise, make prizes?

 

[classic33]

I did it for years as a Parkie..
never fazes me a bit of cleaning...
Must get my intended project on paper at some point..
as above, my artistic slopping on earlier..
Enjoying with a couple of ginger snaps, luvly jubbly..

Colour, no..
It's the material. It determines whatever its uses are.
Ordered a grey PETG and a different make so interesting to run a test piece to see how it lays down, reading some reviews, some are a bit fickle to work with, like my PLA is done using any of four makes.

Enjoying the quiet before Storm Toodles arrive...

You were being paid back then though...
Have you seen how some people leave workplaces these days. Nearly always expecting someone else will clear up after them.
Any ideas on what this intended project might be yet...
Just the two ginger snaps per cuppa these days.

Just wondered as some seem to react to light worse than others.
All PETG/PLA is not equal then! Despite any claims by the manufacturer.

Is she there yet?