Tea?

[Bobby Mhor]

Owdo
Not "Would you like a cuppa" or "Time you were up and about!"
T'is, t'is true
You plan on keeping it there...

Came off alright?
Someone has to...
Any changes for the second test piece...
These supports required for faster printing?

Were they in the same place when placed together, given they were on opposite sides when printing.
Has it worked?

Decided to change the nozzle.....
Must go read up about doing it..
Failing that, hotend replacement?
Maybe tomorrow?
It does follow the usual pattern of needing done...
We'll see....
I'd better find my tools and nozzles, of course.

Supports? for overhangs etc.
Adds time to the prints plus you have to remove them, of course.
The recent blockage eventually cleared, and I wondered if it was anything to do with it.
We'll see...

 

[classic33]

Decided to change the nozzle.....
Must go read up about doing it..
Failing that, hotend replacement?
Maybe tomorrow?
It does follow the usual pattern of needing done...
We'll see....
I'd better find my tools and nozzles, of course.

Long job or just plain awkward...
Haven't you already changed the nozzle one, now you're reading up on it!
Okay, stupid question, hotend replacement?
All tools, and spares not used on a regular basis put up for safe keeping no doubt.

Supports? for overhangs etc.
Adds time to the prints plus you have to remove them, of course.
The recent blockage eventually cleared, and I wondered if it was anything to do with it.
We'll see...

To me, just seems odd that for the same piece(s) one program requires supports the other doesn't. Might be missing something obvious here though.
You got a tip guage, measure the internal size on the nozzle you plan on changing. See how much wear is on it. Might be behind your recent blockage if wear is too much.

Best done when there's no distractions, and you've time for a bit of head scratching...

 

[Bobby Mhor]

Long job or just plain awkward...
Haven't you already changed the nozzle one, now you're reading up on it!
Okay, stupid question, hotend replacement?
All tools, and spares not used on a regular basis put up for safe keeping no doubt.

To me, just seems odd that for the same piece(s) one program requires supports the other doesn't. Might be missing something obvious here though.
You got a tip guage, measure the internal size on the nozzle you plan on changing. See how much wear is on it. Might be behind your recent blockage if wear is too much.

Best done when there's no distractions, and you've time for a bit of head scratching...

I've turned the place upside down and can't find my spare nozzles so I headed off and ordered some..
Bet they turn up in a day or two.
More likely arrive tomorrow afternoon..
if that doesn't work? a new Hotend (?).. Google it much easier....
If that doesn't work, I ain't got a scooby doo...

 

[classic33]

I've turned the place upside down and can't find my spare nozzles so I headed off and ordered some..
Bet they turn up in a day or two.
More likely arrive tomorrow afternoon..
if that doesn't work? a new Hotend (?).. Google it much easier....
If that doesn't work, I ain't got a scooby doo...

Isn't that how you get things to turn up, replace them?
The ones you've ordered, the ones you have or both!
I did search hotend, maybe I should have put 3D printer in as well. Not all results were safe to post.
Hopefully you've no more parts to replace. Just after the driver update as well...

 

[Bobby Mhor]

Afternoon
After a promising start, now slightly wet
Been passed around the health centre
Now home with the Toodles Twins...

 

[classic33]

Afternoon
After a promising start, now slightly wet
Been passed around the health centre
Now home with the Toodles Twins...

Owdo
Similar story down these parts, although the promise didn't las long.
Pillar to post or door to door?
They'll keep you company.

 

[Bobby Mhor]

Isn't that how you get things to turn up, replace them?
The ones you've ordered, the ones you have or both!
I did search hotend, maybe I should have put 3D printer in as well. Not all results were safe to post.
Hopefully you've no more parts to replace. Just after the driver update as well...

Hotend? exciting search item..
It may come to one of them,
nozzles arriving 6-9 pm so no dib dib joint again.
I'll wait until I build up the courage to have a go at the nozzle, hopefully it'll work.
I normally keep any fresh updates but now I'll check if any iffy problems with them.

Coolish day at 8.4c
Low at 2.5c overnight...

 

[Bobby Mhor]

Owdo
Similar story down these parts, although the promise didn't las long.
Pillar to post or door to door?
They'll keep you company.

Afternoon nap.
Toodles snr cycled almost 3 miles on her balance bike earlier, youngest got pushed...
Waiting for them to wake up for a coffee....
Dry again, both me and outside

 

[classic33]

Hotend? exciting search item..
It may come to one of them,
nozzles arriving 6-9 pm so no dib dib joint again.
I'll wait until I build up the courage to have a go at the nozzle, hopefully it'll work.
I normally keep any fresh updates but now I'll check if any iffy problems with them.

Coolish day at 8.4c
Low at 2.5c overnight...

Not now I've put 3D into the search.
Don't appear to come cheap either.
No earlier slots available. Don't they know yer busy...
Nothing in the printer manual showing how it's done?
And if there are...

Slightly warmer, pushing about 1 degree higher than up near you.
Could cover and rain stopped it getting too cold here.

 

[classic33]

Afternoon nap.
Toodles snr cycled almost 3 miles on her balance bike earlier, youngest got pushed...
Waiting for them to wake up for a coffee....
Dry again, both me and outside

You, the Toodle Twins, or all three!
At the rate their going they'll be leaving you behind in no time.
They drink coffee!
And you've a warming drink being supped no doubt. Don't spill it...

 

[Bobby Mhor]

Not now I've put 3D into the search.
Don't appear to come cheap either.
No earlier slots available. Don't they know yer busy...
Nothing in the printer manual showing how it's done?
And if there are...

Slightly warmer, pushing about 1 degree higher than up near you.
Could cover and rain stopped it getting too cold here.

You, the Toodle Twins, or all three!
At the rate their going they'll be leaving you behind in no time.
They drink coffee!
And you've a warming drink being supped no doubt. Don't spill it...

Nah, wee yin was downstairs and coffee maker is there....
One is maybe too young...
Oldest gets a Babychino occasionally...

Plenty of videos around,
I'm not that great mechanically,
I'll have a go tomorrow.

Warmer tonight, just over 10.1c, high today 11.1c at 18.37....

Hopefully getting warmer....(It should I just stuck the heating on upstairs)

Off to log up a load of contacts made earlier.....

Toodlepip

 

[classic33]

Nah, wee yin was downstairs and coffee maker is there....
One is maybe too young...
Oldest gets a Babychino occasionally...

Plenty of videos around,
I'm not that great mechanically,
I'll have a go tomorrow.

Warmer tonight, just over 10.1c, high today 11.1c at 18.37....

Hopefully getting warmer....(It should I just stuck the heating on upstairs)

Off to log up a load of contacts made earlier.....

Toodlepip

Yer coffee maker that noisy? Out of reach, for the Twins.
Only one.
Had to check that, not a local drink at least...

Videos seldom show you how often they got the same piece/parts wrong. Making it look so easy, or awkward, depending on what they're hoping to show you.
You do yerself no favours...
They arrived then!

You've had it warmer up there, and it's headed in yer direction.

It should, if yer heating works...

A quiet day?

Sithi

 

[Bobby Mhor]

Morning all
Another weekend, have more FUN,FUN and extra FUN..
I said so

 

[Bobby Mhor]

Yer coffee maker that noisy? Out of reach, for the Twins.
Only one.
Had to check that, not a local drink at least...

Videos seldom show you how often they got the same piece/parts wrong. Making it look so easy, or awkward, depending on what they're hoping to show you.
You do yerself no favours...
They arrived then!

You've had it warmer up there, and it's headed in yer direction.

It should, if yer heating works...

A quiet day?

Sithi

It makes some funny noises which wake a young 'un....
6.15 to 9.15 delivery time..
Think it was 7ish..

6c just now..
I never really look at forecasts anymore..
I just wiggle my finger in the wind

We old ones can freeze but my little ones..
Must fly busy morning..

 

[classic33]

Morning all
Another weekend, have more FUN,FUN and extra FUN..
I said so

Owdo
Yer getting fairly free with these weekends. Carry on like this and there'll be none left before you realise.
I'll try the have "more FUN" bit before I try "extra FUN". Too much at once might be habit forming.
Bob the Boss! No-one looking over yer shoulder as you type...