Tea?

[classic33]

Good Friday morning
I'll not see you in the peasouper here at the Tower....
Visibility isn't that good..
Enjoy your day..

Owdo this fine Friday morn...
You want to be careful then. Anyone could sneak up on you unseen.
Down to under fifty yards earlier, now clearing.
Sun poking through.
I'll try, promise....

 

[Bobby Mhor]

A game of two halves?
And when yer old stock is used up, they become obsolete...
I'd seen it at the local Currys, when they were doing a demonstration day. Nowt on spools available to buy, from them. All loosely coiled awaiting the spools. Didn't do a very good job on the day. One kept on blowing a fuse, another did everything but what they said it would do.
How long does 300 metres last, once you start printing.

Would that be by appointment only...

It'll turn up on the last day they have before they have to pay a penny.

Nearby depot sounds a lot better than yer other package.

It depends on the job what length it uses,
I'll look at the two halves of the refill spools I printed,

That's one part, I'll find the other later. The other I think will be more...
so at 26.28 m , I get app 12 pieces, using the 1 kg total weight of material, roughly 12.75 piece.
Ignore the cost, I haven't set the cost of a spool yet...

Not much difference between the two then.....
Just done a check, 90p per side so 1.80 per spool, possibly just under 2 british quids when electricity if factored in

 

[Bobby Mhor]

Owdo this fine Friday morn...
You want to be careful then. Anyone could sneak up on you unseen.
Down to under fifty yards earlier, now clearing.
Sun poking through.
I'll try, promise....

Clear now,
news of propagation causing glitches with the continent

 

[classic33]

It depends on the job what length it uses,
I'll look at the two halves of the refill spools I printed,
View attachment 806076
That's one part, I'll find the other later. The other I think will be more...
so at 26.28 m , I get app 12 pieces, using the 1 kg total weight of material, roughly 12.75 piece.
Ignore the cost, I haven't set the cost of a spool yet...

View attachment 806078
Not much difference between the two then.....
Just done a check, 90p per side so 1.80 per spool, possibly just under 2 british quids when electricity if factored in

Sorta figured out a smaller job would use less than a big one. Yer not likely to use a whole spool on one job though, given what you've shown about the supports.

You've lost one already! You'd barely got beyond cleaning it up.
Not tempting fate in case the price goes up.

Not much indeed. Does printing at night make it any cheaper?

 

[classic33]

Clear now,
news of propagation causing glitches with the continent

Good, now get out in't garden and enjoy the sunny weather...
Glitches, everything should be running as normal...

 

[Bobby Mhor]

Good morning all
Lazy day incoming after a busy yesterday,
trip NE to see family, two stops...
Late arrival back....
Roads very quiet heading down..
68 mins from B to Home, nice.
Off to grab some scran, not the usual as we have a smidgen of milk
Enjoy the weekend...

 

[classic33]

Good morning all
Lazy day incoming after a busy yesterday,
trip NE to see family, two stops...
Late arrival back....
Roads very quiet heading down..
68 mins from B to Home, nice.
Off to grab some scran, not the usual as we have a smidgen of milk
Enjoy the weekend...

Owdo
Thought you were having the first of yer lazy days yesterday. I thought you'd have been lying out in't garden enjoying the sun...
Yer thinking about a highland invasion with these trips NE?
Not that late that you missed yer nap time I hope...
You didn't do the usual navigation game of a left turn followed by the second right, pushing yer distance up.
Hopefully yer milk supply issues will have been sorted by now, ready for tomorrow and yer scran was up to scratch.
The same to you, on this lazy weekend.

 

[Bobby Mhor]

Good, now get out in't garden and enjoy the sunny weather...
Glitches, everything should be running as normal...

Sorta figured out a smaller job would use less than a big one. Yer not likely to use a whole spool on one job though, given what you've shown about the supports.

You've lost one already! You'd barely got beyond cleaning it up.
Not tempting fate in case the price goes up.

Not much indeed. Does printing at night make it any cheaper?

If I used a spool on one job, I'd wonder how.
Plate is slightly bigger but not by much.
I ordered band specific PLA to try....
I'm trying to 'empty' older spools with some on it,
see images below (I'm going back to delete any posted this week to save space,
be back soon....

 

[Bobby Mhor]

Live, go look I need some views

 

[classic33]

If I used a spool on one job, I'd wonder how.
Plate is slightly bigger but not by much.
I ordered band specific PLA to try....
I'm trying to 'empty' older spools with some on it,
see images below (I'm going back to delete any posted this week to save space,
be back soon....

Just wondering, out loud, how far the one spool would take you. Mainly because of the supports on pieces you've shown. They seem to take/use more than the actual piece.
Is it self levelling like yer previous one?
Bay City Rollers or U2...
Makes sense to use up what you have before it "goes off".
Does deleting pictures actually save anything?
I'll be waiting...

 

[Bobby Mhor]

Just wondering, out loud, how far the one spool would take you. Mainly because of the supports on pieces you've shown. They seem to take/use more than the actual piece.
Is it self levelling like yer previous one?
Bay City Rollers or U2...
Makes sense to use up what you have before it "goes off".
Does deleting pictures actually save anything?
I'll be waiting...

After 'loading' the model file into the 'slicing' program, you do your tweaks, mostly I change the walls from say 2 to 4 for more strength, then you hit 'slice' and it does its magic and works out everything and also the length of material needed and then approx the weight of it.
Prefer the Rollers, more UPoo got so far ahead with themselves, their heads got stuck somewhere.

Did another buildplate cleaner and was left with just under a metre of PETG so as i mostly use PLA, it got binned..
I'm on lunches today so off to cut some freshly made bread....

 

[classic33]

After 'loading' the model file into the 'slicing' program, you do your tweaks, mostly I change the walls from say 2 to 4 for more strength, then you hit 'slice' and it does its magic and works out everything and also the length of material needed and then approx the weight of it.
Prefer the Rollers, more UPoo got so far ahead with themselves, their heads got stuck somewhere.

Did another buildplate cleaner and was left with just under a metre of PETG so as i mostly use PLA, it got binned..
I'm on lunches today so off to cut some freshly made bread....

Can understand changes where you want more strength. Be a bit of a pain in the rear if you ended up printing it twice. The program show you where all the supports are required, and you add them or does it add them for you.
Can understand your choice of B.C.R., although they did just seem to fade away.

Problems with the plate, or just using up the ends to clean it.
You making the lunches or eating them?