Just wondered if you had seen this article @classic33
https://www.bbc.co.uk/news/articles/c30rrm4z1ggo
https://www.bbc.co.uk/news/articles/c30rrm4z1ggo
You becoming one of those there "influences", showing how things should be done?Did I mention yon YouTube short of the PLA spool, over 1.4 k views
I'll take that, most views out of the shorts I have posted...
Dat'll do me...
Supports, it will put supports on some smaller stuff and will warn you that some supports are needed, track down down Supports, I use Tree Auto which works out where to put them, I find tree is the easiest to work and remove,
I'm basically using the suggested settings and TBH no problems so far, one failed print but as everything looked at, it had to be a flaw in a length of PLA on the spool, I finished the last half of spool with no problem, the Red PLA in video.
I'll avoid that make..
Celebration time....
Da boom boom tish !
The overland spool is in Edinburgh and will be hopefully moved to my local one tomorrow...
Making some boxes for my camera lens filters the noo, must she the Boss for some material to line the bottom of each section.
I've made changes to my cleaning regime,
washing up liquid (or as they say, dish soap),
rub all over the plate then dab kitchen towel into water and clean and dry off.
The daily soul food to prepare..
First I've heard of a re-release. I've still got the original single, on tape.Just wondered if you had seen this article @classic33
https://www.bbc.co.uk/news/articles/c30rrm4z1ggo
Long time no see.Hope you are both as well as can be![]()
Hope you are both as well as can be![]()
Long time no see.
Hope yer doing well.
I could be doing better, like winning the lottery three weeks in a row. Doing it might give me a better chance though
You becoming one of those there "influences", showing how things should be done?
You a bad "influence", or a good un...
Attention spans are getting short these days.
I can understand some supports being needed, but that one you posted where there were more supports on the piece being printed than the actual piece, stood out.
It'll suggest where to place the supports, handy. Saves having to work it out.
Bad PLA. Don't let it play with the rest of them, in the naughty corner to think about what it were doing...
Are there makes that worked with yer "old printer" that are giving problems with yer new one.
I'd celebrate when it gets delivered, not before.
Yer certain it'll be todays tomorrow and not any other tomorrow? You've had at least three "tomorrows" this last week alone.
You didn't keep the cases they came in, shame on you. Or are you after a co-ordinated look. Suppose she says "No", what'll tha do...
That's an odd way of doing the dishes, but each to their own I suppose. Any quicker that way... You could free up some more time for yerself, let the dishes dry on their own, save you the job.
Soul food now eaten...
Was yer milk situation any better this morning.
You got yer porridge this morning then. All due to yer quartermaster(Mrs M)... Only a faint whiff. Has she closed the doors to stop you getting more than a whiff of the pudding!Mrs M was on top of her game today...there is the faint whiff of an Eve's Pudding wafting up the stairs..
No supports needed on that one,
that was more I'd say to be strong enough and to cut down on material. I just had a look at something and it was a third of material going on supports but I'm not sure I will be doing it, a fancy antenna holder..
I am sure it will arrive tomorrow between 1pm and 4pm, ordered on the 27th March and delivered on the 27th April...
Influencers wear about an inch of brown cement on their fizzogs with lots of other 'hide my ugly spots etc' stuff...
1,411 exactly...
Long time no see.
Hope yer doing well.
I could be doing better, like winning the lottery three weeks in a row. Doing it might give me a better chance though
One of two winners on the last draw of 1996 on the Irish Lottery. £300,000 and I sent the wrong ticket back.Statistically it does
but not by an amount that makes any difference in practical terms!
You got yer porridge this morning then. All due to yer quartermaster(Mrs M)... Only a faint whiff. Has she closed the doors to stop you getting more than a whiff of the pudding!
A third isn't as bad as I thought.
More because you wanted it lighter. Wouldn't that make it weaker... Another antenna, you got room for more?
Yer sounding certain any way. Tomorrow will be the day yer package comes off its round the world trip.
Don't those influencers come in all shapes and sizes these days, and that's just the women.
1,413...

There a moose loose...Hoots mon
oooooh toob night, wandering the rubbish strewn beaches of Australia mostly....
I should be doubtful but it is good, old reliable woyal wail....
I've one to extend and one to put up,
I have soldering work to do, tomorrow when Mrs M isn't here?

Owdo there...Good day, fellow Tealandians![]()
Surprise surprise another dry start, a balmy 11c...
Think I may cut the grass today (I'll see),
Mrs M will be away 'doing lunch'
and I'll be eating mine![]()
There a moose loose...
You ever thought of doing that in VR, not just on the tube... Are their beaches as bad as some of ours?
We're on every second day deliveries with Woyal Wail. No first class post either...
Best o'luck on the parcel front. It'll have travelled through a few places on its way to you. If it could only talk when it got to you...
How you gonna extend much less fit another up there. Mrs M doesn't like the smell of soldering?
Talking of smells, did you get anything more than a whiff of the pudding.