Team BKool CycleChat

[rob01792]

Right yes ive just started it

 

[Perky77]

I'm really confused. I'll crack on from my set up and see what happens. I'll do the warm up and see if you pop uo

 

[rob01792]

Right just joined ur ride if u want take it down to 5 then start

 

[berty bassett]

I'm really confused.

YOUR confused !! worse than eastenders !

 

[Soarerv8]

Get a room you two

 

[rob01792]

I'm still confused not sure if I done the right race
well done Perky77 u left me for dust
well @Goldwolfie I couldn't catch ur ghost on that 1
that is 1 ride I wont be repeating anytime soon now

 

[Perky77]

Sorry guys - too much of a novice

What a tough stage that was - the last climb I did a Froome and just went full gas staring down the whole way. Pleased with 1hr06m. Hats off to the ones who do it 25 mins quicker!

 

[Goldwolfie]

Sorry guys - too much of a novice

What a tough stage that was - the last climb I did a Froome and just went full gas staring down the whole way. Pleased with 1hr06m. Hats off to the ones who do it 25 mins quicker!

Well done Martyn and Rob, you got there in the end. Sounds like a painful introduction into the world of Bkool league racing, in more ways than one.

Hope you can both make tonight's Handicap race at 8pm - Martyn, I'm sure Geoff will be explaining the setup for that one.

Welcome and enjoy.

 

[timmers]

Hi there, I have a BKool Pro connected using the ANT+ dongle. Can anyone tell me when they look at the trainer in settings when its paired does it show that FE-c is enabled anywhere? I'm using v3.10 firmware but have been paying monthly up until now.

thanks

 

[theboxers]

I've been beaten, not once , but twice . Well done Rob and Martyn that is a hard stage.

I'll be doing the Hurst Wokingham chaingang stage tonight before the handicap stage .

See you all @8

 

[CXRAndy]

Hi there, I have a BKool Pro connected using the ANT+ dongle. Can anyone tell me when they look at the trainer in settings when its paired does it show that FE-c is enabled anywhere? I'm using v3.10 firmware but have been paying monthly up until now.

thanks

Settings tab has automatic connection and manual. FE c is used when manually connected to trainer, I believe. I doesn't say anything though to indicate FE c protocol

 

[Miljovetare]

Ahh, a fellow Scandinavian, from just across the "lake"...well, location "Sweden" is a bit broad, you could be 1500 km away.
You didn't post the wrong place, but it's just that this thread gets so much more attention. I think most of the admins are either on vacation, or busy getting the most out of the remaining summer. Geoff, aren't' you Chaingang and Mountain Goat admin as well?

Ahh, a fellow Scandinavian, from just across the "lake"...well, location "Sweden" is a bit broad, you could be 1500 km away.
You didn't post the wrong place, but it's just that this thread gets so much more attention. I think most of the admins are either on vacation, or busy getting the most out of the remaining summer. Geoff, aren't' you Chaingang and Mountain Goat admin as well?

I'm in Norrköping, "only" 400 km away then.

I see, I'll just have to be patient, right now the weather is awesome anyway

 

[bobinski]

Settings tab has automatic connection and manual. FE c is used when manually connected to trainer, I believe. I doesn't say anything though to indicate FE c protocol

if you untick auto connection and then click manual you will be taken to a screen where the software then searches for a manual connection. Make sure you spin the pedals and wait up to a minute and the software should eventually present you with the bkool pro and ant+ fec and just tick that and come out of the screen and you are good to go in Zwift etc. i also leave it in manual for bkool rides too.

 

[timmers]

Settings tab has automatic connection and manual. FE c is used when manually connected to trainer, I believe. I doesn't say anything though to indicate FE c protocol

Thanks Andy

 

[bobinski]

https://support.zwift.com/hc/en-us/articles/206332985--Setting-up-a-Bkool-trainer-with-ANT-FE-C