What have you bought for the bike today ?

Page may contain affiliate links. Please see terms for details.

postman

Squire
Location
Meanwoodshire.
S9f999476b275428f8c2d19c06d722076R.jpg_220x220q75.jpg_.avif
not for the bike but my phone,TdF artwork it is lovely.
 

DCLane

Found in the Yorkshire hills ...
Bits over the past month:

- A 9 speed chain for the Giant FCR because it appears the 9 speed that was supposed to be in a box was actually a single speed.
- A Bontrager Arvada saddle.
- A pair of Craft cycling shorts, and
- A Cycplus AS2 Pro USB pump because my 2 year-old Chinese unbranded one has failed.
 

N0bodyOfTheGoat

Über Member
Location
Hampshire, UK
A 4-pack bundle of thicker "gravel" Cyclami metal 45mm valve TPU tubes, that come with levers and patches for less than £36 from Amazon, along with a Shimano optislick gear cable set for less than £14.
 

DCLane

Found in the Yorkshire hills ...
Been a bit spendy, for someone living in Yorkshire, over the past few days:
  • A pair of NOS Notario pedals for the 1948 Claud Butler. They look lovely and shiny in contrast to the deliberately-rusty bike.
  • A seatpost bolt for the Peugeot 653.
  • Two pairs of NOS brake hoods for Shimano Dura-Ace 7800. Found a yellow first, then a white pair.
  • A Dura-Ace 9100 rear derailleur.
  • Eleven Specialized Turbo inner tubes as they were on offer from Sigma Sports, particularly so as they sent me an additional voucher.
  • A couple of carbon headset spacers with the tubes to hit the free postage point.
  • And a Lapierre Audacio 300 that may be a bit too big for me but seemed too cheap not to bid on, which I collected this afternoon:
s-l1600.jpg
 

Andy in Germany

Legendary Member
This:

2026_10_31_Wayfarer_2_0_02.jpg


...and this:


2026_10_31_Wayfarer_2_0_01.jpg




Soda is for the removal of a stuck seat post; many thanks to @Wobblers for the tip that this stuff can break down aluminium

The bottle was chosen because of the long, narrow neck: if I cut a flap in the side of the bottle, I can hold it at a fairly flat angle and use it like a funnel to pour soda and then hot water into the frame.

I wonder if I will get my deposit back afterwards?
 

postman

Squire
Location
Meanwoodshire.
Two name decals for my son ,so he can 'claim' the bike,great value £3-99 for a pair.I am settled in the thought i have stopped,it's been fantastic,i have great memories.I intend during November to go to my favourite cafe and 'retire' with a meal.Cafecafe in Otley going in on the 84x bus service.
 

fossyant

Ride It Like You Stole It!
Location
South Manchester
Pair of lightly used Shimano XC702 shoes off ebay. £50. Already have some XC3's but they are a little tight in a 43, so a summer shoe (thin socks) so I've gone for my usual 44 size in Shimano. Also a pair of 'genuine' cleats - sometimes difficult to get when ordering on-line.

Only issue with the shoes is the bolts on one shoe are rounded - an 'easy out' will sort them.

Gosh, they are my fourth pair of used Shimano shoes I've bought (two others were from new). Have bought used, a spare pair of BOA MW7 boots, a pair of road RW5 boots and a pair of M089's as these are super comfy and my old ones are rather well worn and very old. Bang them in the washing machine and good to go.
 
Last edited:

Punkawallah

Veteran
Soda is for the removal of a stuck seat post; many thanks to @Wobblers for the tip that this stuff can break down aluminium

The bottle was chosen because of the long, narrow neck: if I cut a flap in the side of the bottle, I can hold it at a fairly flat angle and use it like a funnel to pour soda and then hot water into the frame.

I wonder if I will get my deposit back afterwards?

Before you worry about the deposit, worry about the chemical reaction when you add the hot water to the tube. IIRC there is no small amount of heat produced and a lot of ‘frothing’ involved, with risk of explosion. Not recommended with a tube indoors.
Best Practice is to add the powder to the water.
 

Andy in Germany

Legendary Member
Before you worry about the deposit, worry about the chemical reaction when you add the hot water to the tube. IIRC there is no small amount of heat produced and a lot of ‘frothing’ involved, with risk of explosion. Not recommended with a tube indoors.
Best Practice is to add the powder to the water.

I have a plan for that, involving cable tying the frame in a safe location well away from anyone else, eye and hand protection, and leaving it alone to do its thing for an hour or so.
 
Top Bottom